How To Jump Start A 2018 Jeep Compass
Have you found yourself in a sticky situation where your 2018 Jeep Compass won’t start? Don’t worry, we’ve got you covered! In this article, we’ll walk you through the steps on how to jump start your Jeep Compass and get back on the road in no time. So grab your cables and let’s get started!
Table of Contents
- Overview of Jump Starting a 2018 Jeep Compass
- Locating the Battery and Jumper Points
- Connecting the Jumper Cables Safely
- Starting the Dead Battery and Removing the Cables
- Additional Tips for Jump Starting a 2018 Jeep Compass
- Frequently Asked Questions
- To Wrap It Up
Overview of Jump Starting a 2018 Jeep Compass
Jump starting a 2018 Jeep Compass can be a simple and quick process if done correctly. Here are the steps to follow to safely jump start your Jeep Compass:
- Gather the necessary equipment: You will need a set of jumper cables and another vehicle with a working battery to jump start your Jeep Compass.
- Locate the batteries: Pop the hood of both vehicles and locate the batteries. Make sure the vehicles are parked close enough for the jumper cables to reach both batteries.
- Connect the jumper cables: Connect one red clamp to the positive terminal (+) of the dead battery and the other red clamp to the positive terminal (+) of the working battery. Then, connect one black clamp to the negative terminal (-) of the working battery and the other black clamp to an unpainted metal surface on your Jeep Compass to ground the connection.
By following these simple steps, you can safely jump start your 2018 Jeep Compass and get back on the road in no time. Remember to always double-check the connections before starting either vehicle to avoid any potential hazards.
Locating the Battery and Jumper Points
One of the most important steps in jump starting a 2018 Jeep Compass is . The battery in the Jeep Compass is typically located under the hood, towards the front of the vehicle. To access the battery, you may need to remove a cover or panel to reveal the terminals.
Once you have located the battery, it’s important to identify the jumper points. In the 2018 Jeep Compass, the positive jumper point is usually marked with a red cover or symbol, while the negative jumper point is marked with a black cover or symbol. It’s essential to connect the jumper cables to the correct terminals to avoid damaging the vehicle’s electrical system.
To ensure a successful jump start, make sure to follow these steps carefully:
- First, park the assisting vehicle close enough to the Jeep Compass so that the jumper cables can reach both vehicles’ batteries.
- Next, connect the positive (red) jumper cable to the positive terminal on the dead battery, then connect the other end to the positive terminal on the assisting vehicle’s battery.
- Finally, connect the negative (black) jumper cable to the negative terminal on the assisting vehicle’s battery, then attach the other end to an unpainted metal surface on the Jeep Compass, away from the battery. This will help prevent any sparks near the battery.
Connecting the Jumper Cables Safely
When to jump start a 2018 Jeep Compass, it is important to follow the correct steps to avoid any accidents or damage to the vehicles involved. To begin, make sure both vehicles are turned off before starting the process.
Next, locate the battery in both vehicles. In the Jeep Compass, the battery is typically located under the hood on the driver’s side. Once you have located the battery, identify the positive (+) and negative (-) terminals. It is crucial to connect the jumper cables in the correct order to prevent any electrical issues.
Using a set of jumper cables, **connect** the cables in the following order:
– **First, red cable**: Connect one end of the red cable to the positive (+) terminal of the dead battery.
- **Second, red cable**: Connect the other end of the red cable to the positive (+) terminal of the working battery.
– **Third, black cable**: Connect one end of the black cable to the negative (-) terminal of the working battery.
– **Fourth, black cable**: Connect the other end of the black cable to an unpainted metal surface on the Jeep Compass, away from the battery.
Starting the Dead Battery and Removing the Cables
To start the dead battery on your 2018 Jeep Compass, you’ll need a set of jumper cables and another vehicle with a working battery. Once you have those ready, follow these steps to get your Jeep up and running again:
First, make sure both vehicles are turned off and the emergency brakes are engaged. Safety first!
Next, locate the battery in both vehicles. In the Compass, the battery is typically located under the hood, while in the donor vehicle, it may be in the trunk or under the rear seat. Connect the red positive (+) clamp to the positive terminal of the dead battery, then connect the other red clamp to the positive terminal of the donor vehicle’s battery.
After that, connect the black negative (-) clamp to the negative terminal of the donor vehicle’s battery. do not connect the other black clamp to the dead battery – instead, connect it to an unpainted metal surface away from the battery. This will help prevent sparks and potential damage to the electrical system. Now you can start the donor vehicle and let it run for a few minutes to charge up the dead battery before attempting to start your Jeep.
Additional Tips for Jump Starting a 2018 Jeep Compass
When jump starting a 2018 Jeep Compass, there are a few additional tips to keep in mind to ensure a successful procedure.
Here are some extra steps to consider:
- Check the battery terminals: Before connecting the jumper cables, make sure the battery terminals are clean and free of any corrosion. This will help ensure a good electrical connection.
- Use a jump starter pack: If possible, use a portable jump starter pack instead of another vehicle to jump start your Jeep Compass. This can prevent any damage to the vehicle’s electrical system.
- Let the vehicle run: After jump starting the Jeep Compass, let the vehicle run for at least 15-20 minutes to allow the battery to recharge. Avoid turning off the engine right away to prevent the battery from draining again.
Frequently Asked Questions
Q: What are the steps to jump starting a 2018 Jeep Compass?
A: To jump start a 2018 Jeep Compass, you will need a set of jumper cables and another vehicle with a charged battery.
Q: Can I jump start my Jeep Compass on my own?
A: It is recommended to have someone assist you in jump starting your Jeep Compass to ensure safety and proper connection of the jumper cables.
Q: How long should I let my Jeep Compass run after jump starting it?
A: After jump starting your Jeep Compass, it is recommended to let it run for at least 10-15 minutes to allow the battery to fully recharge.
Q: What precautions should I take when jump starting my Jeep Compass?
A: Make sure both vehicles are turned off before connecting the jumper cables, and ensure the cables are connected correctly (positive to positive, negative to negative).
Q: If jump starting my Jeep Compass doesn’t work, what should I do?
A: If jump starting your Jeep Compass doesn’t work, it may indicate a larger issue with the battery or alternator, and it is recommended to seek professional assistance.
To Wrap It Up
As you can see, jump starting a 2018 Jeep Compass is a fairly simple process that can save you time and money in emergency situations. By following the steps outlined in this article, you can safely get your Compass back on the road in no time. Remember to always exercise caution when working with car batteries and seek professional help if you are unsure of what to do. Stay safe and happy driving!